Book An Estimate Now

 

 

We have encountered the article pertaining to Tools You Need to Install a New Bathtub below on the net and think it made good sense to talk about it with you on my blog.

Installing a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably hard project. If the old bathtub is readily accessible, the job can relocate quickly; if you have to open up a wall surface to remove the old tub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the new one. Make sure you have actually qualified on your own for the task and also are comfortable trying it. Instead of working with a service provider to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually already acquired a brand-new bathtub and also do not require to alter the plan of your previous supply of water pipes.
Your tools and product list need to consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Preparing for the Installation

First of all, the supporting framework supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make certain that if the tap includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to stop pressure on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final position.

 

 

Removing Old Taps

If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome due to the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

 

 

Setting up the Bathtub

Making use of both wooden boards under its feet, position the tub in the required placement. The wooden boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet port to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Load the bathtub and additionally examine the overflow outlet as well as the typical electrical outlet for leaks.
Finally, fix the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the tub needs to wait till the bathtub has actually been used a minimum of when as this will settle it right into its last position.

 

 

Suitable New Touches

If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers remain in location in between the faucet and the sink. Secure the tap in place with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Tub

In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealer can break rather early if you do not think about this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you really like more info about Installing A Bathtub? Try leaving a comment down the page. We will be glad to hear your insights about this write-up. We are looking forward that you visit us again in the future. Sharing is good. Helping others is fun. Thanks for taking the time to read it.

Explore Now